Podemos suministrar casi todas las piezas de la trituradora de cono Sandvik H4800 S4800 CH440 CS440.
Por favor, vea
Sandvik HYDROCONE H S type piezas| Número de pieza | Descripción | Número de pieza | Descripción |
| 452.0230-902 | Carcasa inferior | 442.7484-01 | FILLER RING (F, MF) H4000 |
| 442.7201-00 | CUBIERTA DEL CUERPO INFERIOR H4000 | 442.7485-01 | FILLER RING EF,M,MC H4000 |
| 442.7140-00 | PINSHAFT ARM LINER H4000 | 900.1821-00 | TUBO 1-1/4 X 165 KREA SMS 1787 |
| 442.7141-00 | REVESTIMIENTO DE BRAZO ESTRECHO H4000 | 442.7251-02 | ARANDELA-CÓNCAVA 80X30X140 H4000 |
| 442.7146-01 | BOTTOM SHELL BUSH H4000 | 442.7251-03 | ARANDELA DE REVESTIMIENTO CÓNCAVA H4000 |
| 442.7106-01 | COLLAR DE POLVO H4000 | 442.7252-01 | SHIM 1X80X20 1142-32 H4000 |
| 442.7109-01 | ANILLO H4000 | 442.7252-02 | SHIM 3X80X20 1312-00 H4000 |
| 442.7110-01 | LOCATING BAR H4000 | 442.7252-03 | SHIM 5X80X20 1312-00 H4000 |
| 442.7168-01 | SHIM 0.1 THK(0.003) H4000 | 442.7252-04 | SHIM 10X80X20 1312-00 H6000 |
| 442.7168-02 | SHIM 0.5 THK(0.02) H4000 | 442.8687-01 | SCREW M6S 30X360 8.8 H4000 |
| 442.7168-03 | SHIM 0.7 THK(0.03) H4000 | 442.7253-01 | SLEEVE H4000 |
| 442.7168-04 | SHIM 1.0 THK(0.04) H4000 | 442.7271-01 | Arandela de soporte de cóncava H4000 |
| 442.7170-01 | DUST COLLAR GASKET H4000 | 863.0058-00 | ARANDELA DE RESORTE 90X46X5 H4000 |
| 442.7108-01 | SELLO INTERNO ANILLO H4000 | 442.8425-01 | CONCAVE CLAMP RING H4000 |
| 923.0351-00 | Transmisor de temperatura | 442.8290-01 | PASADOR DE FIJACIÓN H4000 |
| 899.0278-00 | TAPA PROTECTORA M42 SW65-2-G68 | 442.7267-90 | ALIMENTADOR DIVISOR ASM LH H4000 |
| 442.9530-01 | SCREW M6S 42X100 8.8 S H4000 | 442.7267-00 | FEED SPLITTER ASM RH H4000 |
| 442.7151-01 | EXCÉNTRICO H4000 | 442.7191-00 | TOLVA DE ALIMENTACIÓN ENSAMBLAJE H4000 |
| 442.9406-01 | ECC BUSHING 32-36-40-44 H4000 | 914.0170-00 | Indicador de nivel de aceite H4000 10 LG |
| 442.9642-01 | ECC BSHG 24-28-32 H4000 | 442.8345-01 | HYDRAULIC PIPE |
| 442.9643-01 | ECC BSG 13-16-20-24 H4000 | 902.0746-00 | VÁLVULA HRSF-3/4R 200KPA H4000 |
| 442.7142-01 | HUB H S4000 | 912.0127-00 | PRESS DROP INDIC PIS3097/2,2 |
| 442.7169-00 | ANILLO S H4000 | 912.0116-00 | Filtro de aire PI0121 H4000 |
| 442.9609-01 | Llave R 25X14X250 S H4000 | 923.0192-00 | TERMÓMETRO IFC60 0-120 L100 |
| 442.7093-00 | GEAR PINION SET S H4000 SPIRAL BVL | 930.0237-00 | Semiacoplamiento D38 05-32-540 |
| 442.7171-01 | ECC GEAR KEY H4000 | 906.0142-00 | Sello mecánico 3884087 H6000 |
| 442.7107-01 | PLACA DE DESGASTE-ECC H4000 | 912.0126-00 | FILTER CARTRIDGE PC230 |
| 853.0646-00 | PIN PRYM N 16 X 45 H4000 | 442.2873-91 | Intercambiador de calor BCF 602-0-4 |
| 442.7163-01 | HYDROSET CYLINDER H4000 | 910.0102-00 | Enfriador de aire-aceite estándar H4000 |
| 442.7166-01 | HYDROSET CYL BUSH H4000 | 900.0160-00 | BUSHING 2.00 X 1.50 |
| 873.0892-00 | O-RING 530 X 7 SMS 1587 H4000 | 906.0390-00 | COMPLETE FAN-(6 BLADE FAN) |
| 442.9672-00 | HYD PISTON ASM H/S4000 | 910.0112-00 | Ventilador axial H4000 (4 aspas) |
| 442.7122-01 | PLACA DE DESGASTE DEL PISTÓN H4000 | 906.0309-00 | ÁLABES DEL IMPULSOR-MK.002 H4000 |
| 442.7121-01 | ARANDELA DE ESCALÓN H4000 | 906.0387-00 | FAN BLADE |
| 442.7112-00 | EMPAQUE CHEVRON-HID H4000 | 910.0067-00 | COOLER CORE IE-2927 |
| 442.7167-01 | PLACA DE SUJECIÓN DEL EMPAQUETADURA H4000 | 972.0531-00 | MOTOR, M2AA112M-4 3601 400VY |
| 442.9663-00 | HYDROSET CYL COVER H4000 | 912.0087-00 | DIRT TRAP SW/0 1 1/2-0 |
| 442.7202-01 | HYD CYL COVER GASKT H4000 | 902.0723-00 | VÁLVULA DE SEGURIDAD DN32 0,7MPA 474122P H4 |
| 873.1276-00 | junta tórica | 442.1774-00 | FLOW SWITCH ASM H4000 |
| 442.9966-901 | Piñón y eje ensamblaje H4800 | 930.0205-00 | Acoplamiento HE 14 Bomba H4000 |
| 442.7506-01 | Piñón eje carcasa S H4000 | 930.0252-00 | Acoplamiento ND 8 |
| 442.7136-01 | PINSHAFT HSG GASKET S H4000 | 843.1445-00 | STUD SCREW |
| 442.7136-02 | PINSHAFT HSG GASKET S H4000 | 906.0270-00 | PUMP P3BAN2004 HL10B02 |
| 442.7136-03 | PINSHAFT HSG GASKET S H4000 | 906.0377-00 | HYDROSET PUMP |
| 868.0282-00 | SPHER ROLLR BEARING H4000 | 972.0182-00 | MOTOR MT90L-2 2,2KW 220-380V |
| 868.0804-00 | SPHER ROLLR BEARING H4000 | 906.0268-00 | BOMBA SOPORTE BL 7SL UNIDAD DE BOMBEO |
| 442.7130-01 | Piñón espaciador del extremo S H4000 | 906.0376-00 | BOMBA SOPORTE |
| 442.7131-01 | SHEAVE END SPACER S H4000 | 906.0269-00 | FOOT BRACKET P200 PUMPING UNIT |
| 873.1208-00 | El sello de aceite anillo BASL H4000 sello de aceite | 919.0165-00 | Acumulador 25L OLAER H4000 |
| 442.9684-01 | PINSHAFT SEAL PLT S H4000 PINION END | 919.0171-00 | BLADDER COMPLETE 25L H4800 |
| 442.7133-01 | PINSHAFT SEAL PLATE H4000 | 919.0184-00 | BLADDER COMPLETE H4000 |
| 442.7134-01 | PINSHAFT SEALPLT GASKET H4000 | 442.1954-01 | Abrazadera de acumulador H4000 |
| 442.7135-01 | PINSHAFT SEALPLT GASKET H4000 | 442.8215-00 | Kit de carga de acumulador |
| 442.7135-02 | PINSHAFT SEALPLT GASKET H4000 | 900.0659-00 | ADAPTADOR R2.0 X R2 |
| 853.0590-00 | Pasador elástico PRYM N 8X28 H4000 | 442.6406-01 | VALVE GUIDE BODY H4000 |
| 442.9937-01 | PIÑÓN EJE H S4000 | 442.6402-01 | VÁLVULA DE RETENCIÓN CARA DE BRIDA H3000 |
| 857.0337-00 | KEY T 22X14X95 SMS 2307 H4000 | 442.6403-01 | VÁLVULA H4000 |
| 857.0336-00 | KEY T 28X16X110 SMS 2307 H4000 | 442.6508-00 | Pieza de conexión |
| 900.0022-00 | CODO 3/4 A4 127 1345, NEGRO | 900.0655-00 | ADAPTADOR R3/4 X R3/4 702-12-12 |
| 900.2026-00 | MAGNETIC PLUG 3/4 S H6000 | 442.8179-00 | ACCUM PIPE PROTECTOR H4000 (SET-L+R) |
| 873.0385-00 | Anillo de sellado Tredo 20 | 912.0128-00 | Base del filtro |
| 442.7577-01 | TAPÓN DE NIVEL DE ACEITE H4000 | 923.0379-00 | MANÓMETRO M20-2 0-6MPA 6 DIA |
| 873.0108-00 | O-RING 3.0X 34.2X 40.2 | 984.0530-00 | CALENTADOR DE INMERSIÓN OE3SB9/3-1650 440V |
| 442.7578-01 | PIPE-PINION END S H4000 | 984.0605-00 | IMM HTR 440V, 2190W S H4000 |
| 442.8703-00 | PIÑÓN EJE BOMBA ENSAMBLAJE 460V, 60HZ | 912.0138-00 | Filtro de aire PI0154 MIC |
| 906.0367-00 | Bomba P3-AAN-0, 75-FL-20-B0 1 | 912.0139-00 | FILTER CARTRIDGE |
| 906.0366-00 | espaciador | 912.0113-00 | Filtro de aire 504-2S 5 micras |
| 930.0248-00 | acoplamiento | 902.0645-00 | Regulador de aire 216-2-8 |
| 906.0365-00 | FOOT FLANGE | 923.0267-00 | Manómetro |
| 923.0193-00 | MANÓMETRO 2748 GLYC D 63 | 864.0046-00 | STAMP B RUBBER COMPRESSION MOUNT |
| 912.0129-00 | FILTER CARTRIDGE PC 507 | 899.0099-00 | Perno de ojo de elevación |
| 442.7238-01 | Arandela-retén de polea H4000 | 442.0800-91 | LEAD-CHECK DE C.S.S. H4000 |
| 442.7259-901 | MAINSHAFT ASSM H4000 | 442.7282-01 | EYEBOLT-PLACA DE ELEVACIÓN S H4000 |
| 442.7100-01 | MAINSHAFT H4000 | 442.7283-00 | LIFTING TOOL-ECC SLV S H4000 |
| 442.7117-01 | MAINSHAFT SLEEVE H4000 | 442.7281-00 | Herramienta de elevación - BTMSHL BSGS H4000 |
| 853.0119-00 | PASADOR PARALELO | 442.8043-00 | Herramienta de elevación - BTMSHL BSGS H4000 |
| 442.7120-01 | MAINSHAFT STEP H4000 | 920.0110-00 | Llave de impacto |
| 442.8332-01 | CABEZA CENTRO H4000 | 920.0151-00 | Llave de impacto |
| 442.7225-01 | MANTLE A M1 H4800 | 442.7284-00 | BARRA DE BAJADA C/TUERCAS S H4000 |
| 442.7225-02 | Manto A M2 H4800 | 843.1333-00 | 双头螺柱 |
| 442.7230-01 | MANTLE B M1 H4800 | 442.7280-00 | Placa de tope del pistón S H4000 |
| 442.7230-02 | MANTLE B M2 H4800 | 442.8794-01 | BTMSHELL SIDE LINER S4000 |
| 442.8039-01 | MANTLE EF M1 H4800 | 442.8796-01 | BTMSHELL SIDE LINER S4000 |
| 442.9073-03 | Manto HC M7 H4800 | 442.8797-01 | BTMSHELL SIDE LINER S4000 |
| 442.7105-00 | Tuerca de la cabeza con anillo de quemado | 442.8798-01 | BTMSHELL SIDE LINER S4000 |
| 442.8333-01 | Tuerca de la cabeza - Interior S H4000 | 442.8795-01 | BTMSHELL SIDE LINER S4000 |
| 442.7115-01 | BURNING RING S H4000 | 442.8068-01 | ECCENTRIC S4000 |
| 442.7102-01 | Anillo de sello de polvo H4000 | 442.8067-01 | ECC BUSH 20-25-30-36 S4000 |
| 442.7103-01 | Anillo de retención H4000 | 442.8092-901 | MAINSHAFT SLEEVE DWL S4000 |
| 442.7523-01 | Retenedor del sello de polvo H4000 | 442.8063-01 | HEADCENTER S4000 |
| 442.7524-01 | SCRAPER H4000 | 442.8070-01 | MANTLE B M1 S4800 |
| 442.7180-00 | TOPSHELL 2-BRAZO H4000 | 442.8070-02 | Manto B M2 S4800 |
| 442.7190-01 | BRAZO DEL SPIDER ESCUDO H4000 | 442.8089-01 | MANTLE A M1 S4800 |
| 900.0425-00 | ACOPLAMIENTO DE TUBERÍA | 442.8089-02 | Manto A M2 S4800 |
| 808.0220-00 | TUBO DE ACERO 10 X 1,5 MM H4000 | 442.8059-01 | TOPSHELL EC2 S4000 |
| 442.7492-01 | SPIDER CAP H4000 | 442.9036-01 | TOPSHELL LINER |
| 912.0114-00 | FILTRO DE AIRE PI0102 R1/4 + INS | 442.8075-01 | ARM SHEILD ASM S4000 |
| 900.0169-00 | NIPPLE 1/4 N8 131 6314, NEGRO | 442.8077-01 | PASADOR DE FIJACIÓN S4000 |
| 900.0002-00 | ELBOW 1/4 A1 127 0016, NEGRO | 442.8078-01 | BUMPER S4000 |
| 873.0838-00 | O-RING 5.7X499.3X510.7 | 442.8079-01 | BUMPER S4000 |
| 442.9408-01 | ARBOLITO BUJE S H4000 | 442.8090-01 | SOPORTE-ADAPTADOR S4000 |
| 442.7193-01 | Sello de aceite anillo-brazo H4000 | 442.9164-00 | SPIDER CAP S4000 |
| 900.0981-00 | PLUG KR1 INSEX ZN 10 H3000, H4000 | 442.8098-00 | LWR CONCAVE C M1 S4800 |
| 442.8416-01 | CÓNCAVO ANILLO EF M1 H4800 | 442.8098-90 | LWR CONCAVE C M2 S4800 |
| 442.8417-01 | CONCAVE RING F M1 H4800 | 442.8114-00 | LWR CONCAVE EC M1 S4800 |
| 442.8417-02 | CONCAVE RING F M2 H4800 | 442.8114-90 | LWR CONCAVE EC M2 S4800 |
| 442.8417-03 | CONCAVE RING F M7 | 452.0273-901 | LWR CONCAVE MC M1 S4800 |
| 442.8418-01 | CÓNCAVO ANILLO MF M1 H4800 | 452.0273-902 | LWR CONCAVE MC M2 S4800 |
| 442.8418-02 | CÓNCAVO ANILLO MF M2 H4800 | 442.8099-00 | UPR CONCAVE C M1 S4800 |
| 442.8419-01 | Anillo de la cóncava M M1 H4800 | 442.8099-90 | UPR CONCAVE C M2 S4800 |
| 442.8419-02 | CONCAVE RING M M2 H4800 | 442.8115-00 | UPR CONCAVE EC M1 S4800 |
| 442.8420-01 | CÓNCAVO ANILLO MC M1 H4800 | 442.8115-90 | UPR CONCAVE EC M2 S4800 |
| 442.8420-02 | CONCAVE RING MC M2 H4800 | 452.0274-901 | UPR CONCAVE MC M1 S4800 |
| 442.8421-01 | CONCAVE RING C M1 H4800 | 452.0274-902 | UPR CONCAVE MC M2 S4800 |
| 442.8421-02 | CONCAVE RING C M2 H4800 | 442.8105-00 | tolva de alimentación S4000 |
| 442.8422-01 | CONCAVE RING EC M1 H4800 | 442.8645-00 | MANGUERA HIDRÁULICA PROTECTORA S4000 |
| 442.8422-02 | CONCAVE RING EC M2 H4800 | 442.1561-01 | KEY-WOODEN WEDGE S4000 |
Nos enfocamos en proporcionar trituradoras y piezas de desgaste para trituradoras.
Symons cone crusher 2 pies, 3 pies, 4.25 pies, 5.5 pies, 7 pies.
Sandvik CH420, CH430, CH440, CH660, CH880, CS420, CS430, CS440, CS660.
HP100, HP200, HP300, HP400, HP500, HP700, HP800.
Y piezas de desgaste para otros trituradores comunes.
CHANGSHA TIGER MACHINERY CO., LTD.
106-7#, No.163 Building, Tianhuabeilu, Changsha County, Hunan, China
Tel:
+86-187 7489 4905
WhatsApp:
+86-187 7489 4905
WeChat:
+86-187 7489 4905
Email:
©2026 CHANGSHA TIGER MACHINERY CO., LTD.